Skip to content

Sonicware LIVEN 8bit warps: MIDI CC, NRPN and OSC map

The Sonicware LIVEN 8bit warps as named OSC addresses — 37 CC — ready to use from Claude (MCP), SuperCollider, Sonic Pi, TouchDesigner or any OSC app via osc-bridge.

Device Sonicware LIVEN 8bit warps
Vendor Sonicware
OSC prefix /liven_8bit_warps
Source 📦 Derived from MIDI Guide (community CC/NRPN data)
Firmware unknown
Revision per pencilresearch canonical CSV
Upstream pencilresearch
Data licence CC-BY-SA-4.0 — MIDI Guide (https://midi.guide) by Pencil Research and contributors
Driver file devices/sonicware/liven_8bit_warps.json

Not tested on the device yet

This driver comes from documentation or community data and has not been checked on real hardware. If you own one, a quick test and a pull request promoting it helps everyone — see CONTRIBUTING.

How do you control it?

Find the MIDI ports, then start the bridge with this driver:

osc-bridge detect        # prints the ready-to-run line for what is plugged in
osc-bridge run --device devices/sonicware/liven_8bit_warps.json --out-port <N> --in-port <M>

Then send OSC to 127.0.0.1:7777, for example:

osc-bridge osc-send /liven_8bit_warps/performance/glide_arpeggiator_type 63

From Claude or any MCP client, the osc-bridge mcp server exposes this driver as liven_8bit_warps: ask “what can the Sonicware LIVEN 8bit warps do?” and it reads this map with list_routes. See the MCP guide.

MIDI CC and NRPN parameters (37)

OSC address CC NRPN (MSB/LSB) Range Nature Section
/liven_8bit_warps/performance/glide_arpeggiator_type 5 0–127 continuous Performance
/liven_8bit_warps/performance/voice_mode 52 0–127 continuous Performance
/liven_8bit_warps/synth/engine 20 0–127 continuous Synth
/liven_8bit_warps/synth/octave 21 0–127 continuous Synth
/liven_8bit_warps/synth/velocity 22 0–127 continuous Synth
/liven_8bit_warps/synth/detune 23 0–127 continuous Synth
/liven_8bit_warps/synth/parameter_1 24 0–127 continuous Synth
/liven_8bit_warps/synth/parameter_2 25 0–127 continuous Synth
/liven_8bit_warps/synth/parameter_3 26 0–127 continuous Synth
/liven_8bit_warps/synth/parameter_4 27 0–127 continuous Synth
/liven_8bit_warps/synth/parameter_5 28 0–127 continuous Synth
/liven_8bit_warps/synth/parameter_6 29 0–127 continuous Synth
/liven_8bit_warps/synth/alias_noise 30 0–127 continuous Synth
/liven_8bit_warps/filter/active 31 0–127 continuous Filter
/liven_8bit_warps/filter/type 32 0–127 continuous Filter
/liven_8bit_warps/filter/cutoff 33 0–127 continuous Filter
/liven_8bit_warps/filter/resonance 34 0–127 continuous Filter
/liven_8bit_warps/filter/co 35 0–127 continuous Filter
/liven_8bit_warps/lfo/rate 36 0–127 continuous LFO
/liven_8bit_warps/lfo/pitch 37 0–127 continuous LFO
/liven_8bit_warps/envelope/attack 38 0–127 continuous Envelope
/liven_8bit_warps/envelope/decay 39 0–127 continuous Envelope
/liven_8bit_warps/envelope/sustain 40 0–127 continuous Envelope
/liven_8bit_warps/envelope/release 41 0–127 continuous Envelope
/liven_8bit_warps/sweep/sweep 42 0–127 continuous Sweep
/liven_8bit_warps/sweep/speed 43 0–127 continuous Sweep
/liven_8bit_warps/sweep/shift 44 0–127 continuous Sweep
/liven_8bit_warps/effects/effect_type 45 0–127 continuous Effects
/liven_8bit_warps/effects/effect_speed 46 0–127 continuous Effects
/liven_8bit_warps/effects/effect_amount 47 0–127 continuous Effects
/liven_8bit_warps/reverb/type 48 0–127 continuous Reverb
/liven_8bit_warps/reverb/reverb 49 0–127 continuous Reverb
/liven_8bit_warps/sequencer/gate_time 50 0–127 continuous Sequencer
/liven_8bit_warps/sequencer/swing 51 0–127 continuous Sequencer
/liven_8bit_warps/sequencer/mode 53 0–127 continuous Sequencer
/liven_8bit_warps/sequencer/mem_level 54 0–127 continuous Sequencer
/liven_8bit_warps/sequencer/parameter_lock 55 0–127 continuous Sequencer

Performance MIDI

Notes, pitch bend and any CC are also available: /liven_8bit_warps/note/on <note> <velocity>, /liven_8bit_warps/cc/<number> <value>, /liven_8bit_warps/pitchbend <0-16383>, /liven_8bit_warps/program_change <n>.

Limitations

CC/NRPN only. SysEx (preset management, display control, bulk dump/load, vendor-proprietary opcodes) is NOT covered by pencilresearch. To extend this device with SysEx, sniff the vendor editor, add `sysex.header/footer` + `commands` blocks, and use `update_device.md` PR template.