Roland JV-1010: MIDI CC, NRPN and OSC map¶
The Roland JV-1010 as named OSC addresses — 24 CC — ready to use from Claude (MCP), SuperCollider, Sonic Pi, TouchDesigner or any OSC app via osc-bridge.
| Device | Roland JV-1010 |
|---|---|
| Vendor | Roland |
| OSC prefix | /jv_1010 |
| Source | 📦 Derived from MIDI Guide (community CC/NRPN data) |
| Firmware | unknown |
| Revision | per pencilresearch canonical CSV |
| Upstream | pencilresearch |
| Data licence | CC-BY-SA-4.0 — MIDI Guide (https://midi.guide) by Pencil Research and contributors |
| Driver file | devices/roland/jv_1010.json |
Not tested on the device yet
This driver comes from documentation or community data and has not been checked on real hardware. If you own one, a quick test and a pull request promoting it helps everyone — see CONTRIBUTING.
How do you control it?¶
Find the MIDI ports, then start the bridge with this driver:
osc-bridge detect # prints the ready-to-run line for what is plugged in
osc-bridge run --device devices/roland/jv_1010.json --out-port <N> --in-port <M>
Then send OSC to 127.0.0.1:7777, for example:
From Claude or any MCP client, the osc-bridge mcp server exposes this driver as jv_1010: ask “what can the Roland JV-1010 do?” and it reads this map with list_routes. See the MCP guide.
MIDI CC and NRPN parameters (24)¶
| OSC address | CC | NRPN (MSB/LSB) | Range | Nature | Section |
|---|---|---|---|---|---|
/jv_1010/cutoff_frequency |
74 | 0–127 | continuous | ||
/jv_1010/resonance |
71 | 0–127 | continuous | ||
/jv_1010/modulation |
1 | 0–127 | continuous | ||
/jv_1010/env_release |
72 | 0–127 | continuous | ||
/jv_1010/env_attack |
73 | 0–127 | continuous | ||
/jv_1010/volume |
7 | 0–127 | continuous | ||
/jv_1010/balance |
8 | 0–127 | continuous | ||
/jv_1010/pan |
10 | 0–127 | continuous | ||
/jv_1010/reverb_send |
91 | 0–127 | continuous | ||
/jv_1010/chorus_send |
93 | 0–127 | continuous | ||
/jv_1010/level_env_tone1 |
80 | 0–127 | continuous | ||
/jv_1010/level_env_tone2 |
81 | 0–127 | continuous | ||
/jv_1010/level_env_tone3 |
82 | 0–127 | continuous | ||
/jv_1010/level_env_tone4 |
83 | 0–127 | continuous | ||
/jv_1010/portamento_on_off |
65 | 0–127 | continuous | ||
/jv_1010/portamento_amount |
84 | 0–127 | continuous | ||
/jv_1010/portamento_time |
5 | 0–127 | continuous | ||
/jv_1010/breath_type |
2 | 0–127 | continuous | ||
/jv_1010/foot_type |
4 | 0–127 | continuous | ||
/jv_1010/expression |
11 | 0–127 | continuous | ||
/jv_1010/hold1 |
64 | 0–127 | continuous | ||
/jv_1010/hold2 |
69 | 0–127 | continuous | ||
/jv_1010/sostenuto |
66 | 0–127 | continuous | ||
/jv_1010/soft |
67 | 0–127 | continuous |
Performance MIDI¶
Notes, pitch bend and any CC are also available: /jv_1010/note/on <note> <velocity>, /jv_1010/cc/<number> <value>, /jv_1010/pitchbend <0-16383>, /jv_1010/program_change <n>.
Limitations¶
CC/NRPN only. SysEx (preset management, display control, bulk dump/load, vendor-proprietary opcodes) is NOT covered by pencilresearch. To extend this device with SysEx, sniff the vendor editor, add `sysex.header/footer` + `commands` blocks, and use `update_device.md` PR template.