OTO Machines FX BIM: MIDI CC, NRPN and OSC map¶
The OTO Machines FX BIM as named OSC addresses — 20 CC — ready to use from Claude (MCP), SuperCollider, Sonic Pi, TouchDesigner or any OSC app via osc-bridge.
| Device | OTO Machines FX BIM |
|---|---|
| Vendor | OTO Machines FX |
| OSC prefix | /bim |
| Source | 📦 Derived from MIDI Guide (community CC/NRPN data) |
| Firmware | unknown |
| Revision | per pencilresearch canonical CSV |
| Upstream | pencilresearch |
| Data licence | CC-BY-SA-4.0 — MIDI Guide (https://midi.guide) by Pencil Research and contributors |
| Driver file | devices/oto-machines-fx/bim.json |
Not tested on the device yet
This driver comes from documentation or community data and has not been checked on real hardware. If you own one, a quick test and a pull request promoting it helps everyone — see CONTRIBUTING.
How do you control it?¶
Find the MIDI ports, then start the bridge with this driver:
osc-bridge detect # prints the ready-to-run line for what is plugged in
osc-bridge run --device devices/oto-machines-fx/bim.json --out-port <N> --in-port <M>
Then send OSC to 127.0.0.1:7777, for example:
From Claude or any MCP client, the osc-bridge mcp server exposes this driver as bim: ask “what can the OTO Machines FX BIM do?” and it reads this map with list_routes. See the MCP guide.
MIDI CC and NRPN parameters (20)¶
| OSC address | CC | NRPN (MSB/LSB) | Range | Nature | Section |
|---|---|---|---|---|---|
/bim/delay |
12 | 0–127 | continuous | ||
/bim/feedback |
13 | 0–127 | continuous | ||
/bim/mix |
14 | 0–127 | continuous | ||
/bim/lfo_rate |
15 | 0–127 | continuous | ||
/bim/lfo_depth |
16 | 0–127 | continuous | ||
/bim/active |
17 | 0–127 | continuous | ||
/bim/division |
18 | 0–127 | continuous | ||
/bim/range |
19 | 0–127 | continuous | ||
/bim/fx_type |
20 | 0–127 | continuous | ||
/bim/in_gain |
21 | 0–127 | continuous | ||
/bim/hpf |
22 | 0–127 | continuous | ||
/bim/lpf |
23 | 0–127 | continuous | ||
/bim/feedback_filters |
24 | 0–127 | continuous | ||
/bim/offset |
25 | 0–127 | continuous | ||
/bim/lfo_wave |
26 | 0–127 | continuous | ||
/bim/lfo_range |
27 | 0–127 | continuous | ||
/bim/freeze |
28 | 0–127 | continuous | ||
/bim/freeze_reverse |
29 | 0–127 | continuous | ||
/bim/lfo_division |
30 | 0–127 | continuous | ||
/bim/lfo_phase_reset |
31 | 0–127 | continuous |
Performance MIDI¶
Notes, pitch bend and any CC are also available: /bim/note/on <note> <velocity>, /bim/cc/<number> <value>, /bim/pitchbend <0-16383>, /bim/program_change <n>.
Limitations¶
CC/NRPN only. SysEx (preset management, display control, bulk dump/load, vendor-proprietary opcodes) is NOT covered by pencilresearch. To extend this device with SysEx, sniff the vendor editor, add `sysex.header/footer` + `commands` blocks, and use `update_device.md` PR template.