Make Noise 0-Coast: MIDI CC, NRPN and OSC map¶
The Make Noise 0-Coast as named OSC addresses — 17 CC — ready to use from Claude (MCP), SuperCollider, Sonic Pi, TouchDesigner or any OSC app via osc-bridge.
| Device | Make Noise 0-Coast |
|---|---|
| Vendor | Make Noise |
| OSC prefix | /0_coast |
| Source | 📦 Derived from MIDI Guide (community CC/NRPN data) |
| Firmware | unknown |
| Revision | per pencilresearch canonical CSV |
| Upstream | pencilresearch |
| Data licence | CC-BY-SA-4.0 — MIDI Guide (https://midi.guide) by Pencil Research and contributors |
| Driver file | devices/make-noise/0_coast.json |
Not tested on the device yet
This driver comes from documentation or community data and has not been checked on real hardware. If you own one, a quick test and a pull request promoting it helps everyone — see CONTRIBUTING.
How do you control it?¶
Find the MIDI ports, then start the bridge with this driver:
osc-bridge detect # prints the ready-to-run line for what is plugged in
osc-bridge run --device devices/make-noise/0_coast.json --out-port <N> --in-port <M>
Then send OSC to 127.0.0.1:7777, for example:
From Claude or any MCP client, the osc-bridge mcp server exposes this driver as 0_coast: ask “what can the Make Noise 0-Coast do?” and it reads this map with list_routes. See the MCP guide.
MIDI CC and NRPN parameters (17)¶
| OSC address | CC | NRPN (MSB/LSB) | Range | Nature | Section |
|---|---|---|---|---|---|
/0_coast/arpeggiator/switch |
117 | 0–127 | continuous | Arpeggiator | |
/0_coast/arpeggiator/type |
119 | 0–127 | continuous | Arpeggiator | |
/0_coast/general/legato_switch |
118 | 0–127 | continuous | General | |
/0_coast/midi_and_cv_control/midi_a_channel |
102 | 0–127 | continuous | MIDI and CV control | |
/0_coast/midi_and_cv_control/midi_b_channel |
103 | 0–127 | continuous | MIDI and CV control | |
/0_coast/midi_and_cv_control/midi_channel_a_cv |
104 | 0–127 | continuous | MIDI and CV control | |
/0_coast/midi_and_cv_control/midi_channel_b_cv |
105 | 0–127 | continuous | MIDI and CV control | |
/0_coast/midi_and_cv_control/midi_channel_a_gate |
106 | 0–127 | continuous | MIDI and CV control | |
/0_coast/midi_and_cv_control/midi_channel_b_gate |
107 | 0–127 | continuous | MIDI and CV control | |
/0_coast/general/pitch_bend_scale_a |
108 | 0–127 | continuous | General | |
/0_coast/general/pitch_bend_scale_b |
109 | 0–127 | continuous | General | |
/0_coast/general/aftertouch_scale_a |
110 | 0–127 | continuous | General | |
/0_coast/general/aftertouch_scale_b |
111 | 0–127 | continuous | General | |
/0_coast/general/velocity_scale_a |
112 | 0–127 | continuous | General | |
/0_coast/general/velocity_scale_b |
113 | 0–127 | continuous | General | |
/0_coast/midi_and_cv_control/midi_block_switch |
114 | 0–127 | continuous | MIDI and CV control | |
/0_coast/general/tempo_in_divisor |
116 | 0–127 | continuous | General |
Performance MIDI¶
Notes, pitch bend and any CC are also available: /0_coast/note/on <note> <velocity>, /0_coast/cc/<number> <value>, /0_coast/pitchbend <0-16383>, /0_coast/program_change <n>.
Limitations¶
CC/NRPN only. SysEx (preset management, display control, bulk dump/load, vendor-proprietary opcodes) is NOT covered by pencilresearch. To extend this device with SysEx, sniff the vendor editor, add `sysex.header/footer` + `commands` blocks, and use `update_device.md` PR template.