KORG Electribe ER-1: MIDI CC, NRPN and OSC map¶
The KORG Electribe ER-1 as named OSC addresses — 17 NRPN — ready to use from Claude (MCP), SuperCollider, Sonic Pi, TouchDesigner or any OSC app via osc-bridge.
| Device | KORG Electribe ER-1 |
|---|---|
| Vendor | KORG |
| OSC prefix | /electribe_er_1 |
| Source | 📦 Derived from MIDI Guide (community CC/NRPN data) |
| Firmware | unknown |
| Revision | per pencilresearch canonical CSV |
| Upstream | pencilresearch |
| Data licence | CC-BY-SA-4.0 — MIDI Guide (https://midi.guide) by Pencil Research and contributors |
| Driver file | devices/korg/electribe_er_1.json |
Not tested on the device yet
This driver comes from documentation or community data and has not been checked on real hardware. If you own one, a quick test and a pull request promoting it helps everyone — see CONTRIBUTING.
How do you control it?¶
Find the MIDI ports, then start the bridge with this driver:
osc-bridge detect # prints the ready-to-run line for what is plugged in
osc-bridge run --device devices/korg/electribe_er_1.json --out-port <N> --in-port <M>
Then send OSC to 127.0.0.1:7777, for example:
From Claude or any MCP client, the osc-bridge mcp server exposes this driver as electribe_er_1: ask “what can the KORG Electribe ER-1 do?” and it reads this map with list_routes. See the MCP guide.
MIDI CC and NRPN parameters (17)¶
| OSC address | CC | NRPN (MSB/LSB) | Range | Nature | Section |
|---|---|---|---|---|---|
/electribe_er_1/oscillator/pitch |
2 / 2 | 0–127 | continuous | Oscillator | |
/electribe_er_1/oscillator/mod_depth |
2 / 6 | 0–127 | continuous | Oscillator | |
/electribe_er_1/oscillator/mod_speed |
2 / 5 | 0–127 | continuous | Oscillator | |
/electribe_er_1/oscillator/mod_type |
2 / 4 | 0–5 | discrete | Oscillator | |
/electribe_er_1/oscillator/wave |
2 / 3 | 0–127 | continuous | Oscillator | |
/electribe_er_1/amp/decay |
2 / 8 | 0–127 | continuous | Amp | |
/electribe_er_1/amp/level |
2 / 7 | 0–127 | continuous | Amp | |
/electribe_er_1/amp/pan |
2 / 1 | 0–127 | continuous | Amp | |
/electribe_er_1/amp/low_boost |
2 / 0 | 0–127 | continuous | Amp | |
/electribe_er_1/motion_seq/motion_seq |
2 / 9 | 0–2 | discrete | Motion Seq | |
/electribe_er_1/delay/type |
2 / 107 | 0–2 | discrete | Delay | |
/electribe_er_1/delay/depth |
2 / 100 | 0–127 | continuous | Delay | |
/electribe_er_1/delay/time |
2 / 101 | 0–127 | continuous | Delay | |
/electribe_er_1/ring_mod/1 |
2 / 102 | 0–127 | continuous | Ring Mod | |
/electribe_er_1/ring_mod/2 |
2 / 103 | 0–127 | continuous | Ring Mod | |
/electribe_er_1/mute/synths |
2 / 109 | 0–15 | discrete | Mute | |
/electribe_er_1/mute/pcm_audio |
2 / 110 | 0–63 | continuous | Mute |
Performance MIDI¶
Notes, pitch bend and any CC are also available: /electribe_er_1/note/on <note> <velocity>, /electribe_er_1/cc/<number> <value>, /electribe_er_1/pitchbend <0-16383>, /electribe_er_1/program_change <n>.
Limitations¶
CC/NRPN only. SysEx (preset management, display control, bulk dump/load, vendor-proprietary opcodes) is NOT covered by pencilresearch. To extend this device with SysEx, sniff the vendor editor, add `sysex.header/footer` + `commands` blocks, and use `update_device.md` PR template.