KORG electribe 2 (EMX 2): MIDI CC, NRPN and OSC map¶
The KORG electribe 2 (EMX 2) as named OSC addresses — 23 CC — ready to use from Claude (MCP), SuperCollider, Sonic Pi, TouchDesigner or any OSC app via osc-bridge.
| Device | KORG electribe 2 (EMX 2) |
|---|---|
| Vendor | KORG |
| OSC prefix | /electribe_2_emx_2 |
| Source | 📦 Derived from MIDI Guide (community CC/NRPN data) |
| Firmware | unknown |
| Revision | per pencilresearch canonical CSV |
| Upstream | pencilresearch |
| Data licence | CC-BY-SA-4.0 — MIDI Guide (https://midi.guide) by Pencil Research and contributors |
| Driver file | devices/korg/electribe_2_emx_2.json |
Not tested on the device yet
This driver comes from documentation or community data and has not been checked on real hardware. If you own one, a quick test and a pull request promoting it helps everyone — see CONTRIBUTING.
How do you control it?¶
Find the MIDI ports, then start the bridge with this driver:
osc-bridge detect # prints the ready-to-run line for what is plugged in
osc-bridge run --device devices/korg/electribe_2_emx_2.json --out-port <N> --in-port <M>
Then send OSC to 127.0.0.1:7777, for example:
From Claude or any MCP client, the osc-bridge mcp server exposes this driver as electribe_2_emx_2: ask “what can the KORG electribe 2 (EMX 2) do?” and it reads this map with list_routes. See the MCP guide.
MIDI CC and NRPN parameters (23)¶
| OSC address | CC | NRPN (MSB/LSB) | Range | Nature | Section |
|---|---|---|---|---|---|
/electribe_2_emx_2/amp/level |
7 | 0–127 | continuous | Amp | |
/electribe_2_emx_2/amp/pan |
10 | 0–127 | continuous | Amp | |
/electribe_2_emx_2/eg/attack |
73 | 0–127 | continuous | EG | |
/electribe_2_emx_2/eg/decay_release |
72 | 0–127 | continuous | EG | |
/electribe_2_emx_2/filter/cutoff |
74 | 0–127 | continuous | Filter | |
/electribe_2_emx_2/filter/resonance |
71 | 0–127 | continuous | Filter | |
/electribe_2_emx_2/filter/eg_intensity |
83 | 0–127 | continuous | Filter | |
/electribe_2_emx_2/insert_fx/off_on |
104 | 0–127 | continuous | Insert FX | |
/electribe_2_emx_2/insert_fx/edit |
87 | 0–127 | continuous | Insert FX | |
/electribe_2_emx_2/master_fx/x |
102 | 0–127 | continuous | Master FX | |
/electribe_2_emx_2/master_fx/y |
103 | 0–127 | continuous | Master FX | |
/electribe_2_emx_2/master_fx/send_on_off |
105 | 0–127 | continuous | Master FX | |
/electribe_2_emx_2/master_fx/on_off |
106 | 0–127 | continuous | Master FX | |
/electribe_2_emx_2/modulation/depth |
85 | 0–127 | continuous | Modulation | |
/electribe_2_emx_2/modulation/speed |
86 | 0–127 | continuous | Modulation | |
/electribe_2_emx_2/oscillators/oscillator_pitch |
80 | 0–127 | continuous | Oscillators | |
/electribe_2_emx_2/oscillators/oscillator_glide |
81 | 0–127 | continuous | Oscillators | |
/electribe_2_emx_2/oscillators/oscillator_edit |
82 | 0–127 | continuous | Oscillators | |
/electribe_2_emx_2/global/bank_select_msb |
0 | 0–127 | continuous | Global | |
/electribe_2_emx_2/global/bank_select_lsb |
32 | 0–127 | continuous | Global | |
/electribe_2_emx_2/global/all_sound_off |
120 | 0–0 | continuous | Global | |
/electribe_2_emx_2/global/reset_all_controllers |
121 | 0–0 | continuous | Global | |
/electribe_2_emx_2/global/all_note_off |
123 | 0–0 | continuous | Global |
Performance MIDI¶
Notes, pitch bend and any CC are also available: /electribe_2_emx_2/note/on <note> <velocity>, /electribe_2_emx_2/cc/<number> <value>, /electribe_2_emx_2/pitchbend <0-16383>, /electribe_2_emx_2/program_change <n>.
Limitations¶
CC/NRPN only. SysEx (preset management, display control, bulk dump/load, vendor-proprietary opcodes) is NOT covered by pencilresearch. To extend this device with SysEx, sniff the vendor editor, add `sysex.header/footer` + `commands` blocks, and use `update_device.md` PR template.