Electra Community Polyexciter (13): MIDI CC, NRPN and OSC map¶
The Electra Community Polyexciter (13) as named OSC addresses — 66 CC — ready to use from Claude (MCP), SuperCollider, Sonic Pi, TouchDesigner or any OSC app via osc-bridge.
| Device | Electra Community Polyexciter (13) |
|---|---|
| Vendor | Electra Community |
| OSC prefix | /polyexciter_13 |
| Source | 🎛️ Derived from an Electra One community preset |
| Revision | per Electra preset |
| Upstream | electra-preset |
| Driver file | devices/electra-community/polyexciter_13.json |
Not tested on the device yet
This driver comes from documentation or community data and has not been checked on real hardware. If you own one, a quick test and a pull request promoting it helps everyone — see CONTRIBUTING.
How do you control it?¶
Find the MIDI ports, then start the bridge with this driver:
osc-bridge detect # prints the ready-to-run line for what is plugged in
osc-bridge run --device devices/electra-community/polyexciter_13.json --out-port <N> --in-port <M>
Then send OSC to 127.0.0.1:7777, for example:
From Claude or any MCP client, the osc-bridge mcp server exposes this driver as polyexciter_13: ask “what can the Electra Community Polyexciter (13) do?” and it reads this map with list_routes. See the MCP guide.
MIDI CC and NRPN parameters (66)¶
| OSC address | CC | NRPN (MSB/LSB) | Range | Nature | Section |
|---|---|---|---|---|---|
/polyexciter_13/attn_1 |
1 | -200–200 | continuous | ||
/polyexciter_13/attn_2 |
2 | -200–200 | continuous | ||
/polyexciter_13/attn_3 |
3 | -200–200 | continuous | ||
/polyexciter_13/attn_4 |
4 | -200–200 | continuous | ||
/polyexciter_13/attn_5 |
5 | -200–200 | continuous | ||
/polyexciter_13/attn_6 |
6 | -200–200 | continuous | ||
/polyexciter_13/mode |
7 | 0–2 | continuous | ||
/polyexciter_13/table |
8 | -1–999 | continuous | ||
/polyexciter_13/exciter |
9 | 0–127 | continuous | ||
/polyexciter_13/exciter_length |
10 | 1–597 | continuous | ||
/polyexciter_13/tone |
11 | 0–127 | continuous | ||
/polyexciter_13/damp |
12 | 0–100 | continuous | ||
/polyexciter_13/release_damp |
13 | 0–100 | continuous | ||
/polyexciter_13/pressure |
14 | 0–127 | continuous | ||
/polyexciter_13/veloc_strike |
15 | 0–100 | continuous | ||
/polyexciter_13/veloc_tone |
16 | -100–100 | continuous | ||
/polyexciter_13/veloc_damp |
17 | -100–100 | continuous | ||
/polyexciter_13/veloc_excite |
18 | -127–127 | continuous | ||
/polyexciter_13/pitch_damp |
19 | -100–100 | continuous | ||
/polyexciter_13/pitch_excite |
20 | -100–100 | continuous | ||
/polyexciter_13/pitch_lpf |
21 | -100–100 | continuous | ||
/polyexciter_13/press_excite |
22 | -127–127 | continuous | ||
/polyexciter_13/env_pitch |
23 | -120–120 | continuous | ||
/polyexciter_13/env_exciter |
24 | -127–127 | continuous | ||
/polyexciter_13/lfo_pitch |
25 | -200–200 | continuous | ||
/polyexciter_13/lfo_exciter |
26 | -127–127 | continuous | ||
/polyexciter_13/lfo_speed |
27 | -100–100 | continuous | ||
/polyexciter_13/attack_time |
28 | 0–127 | continuous | ||
/polyexciter_13/decay_time |
29 | 0–127 | continuous | ||
/polyexciter_13/sustain_level |
30 | -127–127 | continuous | ||
/polyexciter_13/release_time |
31 | 0–127 | continuous | ||
/polyexciter_13/coarse_tune |
32 | -60–60 | continuous | ||
/polyexciter_13/fine_tune |
33 | -100–100 | continuous | ||
/polyexciter_13/gain |
34 | -40–24 | continuous | ||
/polyexciter_13/sustain |
35 | 0–1 | switch | ||
/polyexciter_13/bend_range |
36 | 0–48 | continuous | ||
/polyexciter_13/chord_enable |
37 | 0–7 | continuous | ||
/polyexciter_13/chord_key |
38 | -12–12 | continuous | ||
/polyexciter_13/chord_scale |
39 | 0–7 | continuous | ||
/polyexciter_13/chord_shape |
40 | 0–13 | continuous | ||
/polyexciter_13/chrd_inversion |
41 | 0–3 | continuous | ||
/polyexciter_13/arpeg_1_mode |
42 | 0–14 | continuous | ||
/polyexciter_13/arpeg_2_mode |
43 | 0–14 | continuous | ||
/polyexciter_13/arpeg_3_mode |
44 | 0–14 | continuous | ||
/polyexciter_13/arpeg_1_range |
45 | 1–3 | continuous | ||
/polyexciter_13/arpeg_2_range |
46 | 1–3 | continuous | ||
/polyexciter_13/arpeg_3_range |
47 | 1–3 | continuous | ||
/polyexciter_13/chorus_mode |
51 | 0–2 | continuous | ||
/polyexciter_13/delay_mode |
52 | 0–2 | continuous | ||
/polyexciter_13/delay_level |
53 | -40–0 | continuous | ||
/polyexciter_13/delay_time |
54 | 1–18 | continuous | ||
/polyexciter_13/delay_feedback |
55 | 0–100 | continuous | ||
/polyexciter_13/unison |
56 | 1–8 | continuous | ||
/polyexciter_13/unison_detune |
57 | 0–100 | continuous | ||
/polyexciter_13/lowpass_filter |
50 | 0–127 | continuous | ||
/polyexciter_13/scala_mts |
48 | 0–127 | continuous | ||
/polyexciter_13/scala_kbm |
49 | 0–127 | continuous | ||
/polyexciter_13/output_spread |
58 | -100–100 | continuous | ||
/polyexciter_13/output_mode |
59 | 0–3 | continuous | ||
/polyexciter_13/input_mode |
60 | 0–18 | continuous | ||
/polyexciter_13/sustain_mode |
61 | 0–1 | switch | ||
/polyexciter_13/midi_vel_curve |
62 | 0–3 | continuous | ||
/polyexciter_13/ext_exciter_in |
63 | 0–6 | continuous | ||
/polyexciter_13/pitch_bend_in |
64 | 0–6 | continuous | ||
/polyexciter_13/arp_reset_in |
65 | 0–6 | continuous | ||
/polyexciter_13/max_voices |
66 | 1–8 | continuous |
Performance MIDI¶
Notes, pitch bend and any CC are also available: /polyexciter_13/note/on <note> <velocity>, /polyexciter_13/cc/<number> <value>, /polyexciter_13/pitchbend <0-16383>, /polyexciter_13/program_change <n>.
Limitations¶
Imported from an Electra One community preset. The mapping reflects the preset author's editorial choices: parameter naming, ranges, and which params are exposed. Untested on hardware in this repo.